Requirements and Applications of Medical-Grade Adhesives (Endoscopic Capsules)

This article discusses the use of adhesives in capsule endoscopy. A capsule endoscope is a miniature device that, once swallowed, can capture images of the digestive tract; its shell contains several hundred components—including a lens, an image sensor chip, LEDs, a battery, and an antenna—whose fixation and sealing at every point rely on adhesives, which are also critical to yield and safety.

01 First, take a clear look: where are the 11 adhesive dots located?

Although a capsule is small, it contains all the essential components. From the imaging end to the rear, they are arranged in the following order: an optical window, a lens stack, a CMOS image sensor, a white LED, a PCB/ASIC, a silver oxide battery, a spiral antenna, and a magnetic switch. These components are fixed together and hermetically sealed; virtually every part incorporates adhesive.

Based on their location within the capsule and their intended function, these 11 adhesive application points can be broadly divided into three categories:

  • Optical path components: optical windows, lens stacks, CIS mounting, and LED mounting—must be clearly visible.
  • Seals: edge sealing, housing joints, and battery securing—all must be properly sealed.
  • Functional components: antenna conductivity, encapsulation coating, and magnetic control element fixation—must ensure reliable connectivity and effective protection.

02 Before selecting a model, first pass three stringent thresholds

If you fail to clear these basic requirements, no matter how appealing the other specifications may be, they will be useless.

  • Biocompatibility: ISO 10993 series + USP Class VI; tests must include cytotoxicity, sensitization, intradermal irritation, systemic toxicity, implantation, hemolysis, and others. Once the capsule is swallowed and the gel comes into direct or indirect contact with the mucosa of the digestive tract, this stage is the most stringent.
  • Sterilization resistance: compatible with gamma radiation, ethylene oxide (ETO), electron beams, and high-pressure steam sterilization. Capsules are generally sterilized before leaving the factory; the gel must not consequently crack, become brittle, yellow discolor, or lose its adhesiveness.
  • Solvent-free single-component formulation: no residue after photopolymerization, resulting in a clean process. Intraoperative devices must not contain solvent residues; dispensing must be controllable and capable of automatic detection.

03 When selecting a model, the three variables are what truly matter

Once you have crossed the threshold, proceed with your selection based primarily on three variables.

Light must not penetrate (optical path component) → optical-grade UV adhesive. Since the window, lens, and chip are all located within the imaging optical path, the adhesive must have high light transmittance, low yellowing, low stress, and low shrinkage. Common optical UV adhesives have a refractive index ranging from 1.46 to 1.57; the index should be matched as closely as possible to that of the window material to minimize interfacial reflection. The volumetric shrinkage during curing should also be kept as low as possible—some formulations achieve approximately 0.9%—otherwise, the resulting stress can cause window deformation and imaging distortion.

UV light cannot attain these areas (dark zones) → dual-cure UV adhesive. The joints between the lens module and the main body, as well as deep cavities, are completely out of attain of UV light. If UV curing alone is used, these areas will remain uncured soft zones. A UV humidifying gas or a dual-cure system with direct contact can be employed so that the material can cure into a complete sealing ring even when UV light cannot attain it.

Whether electrical or thermal conductivity is required → conductive adhesive / thermal conductive adhesive. In applications such as antennas, battery terminals, CIS, and LEDs, either electrical continuity or heat dissipation is required, necessitating adhesives with electrical or thermal conductivity.

Next, consider strength and flexibility: for structural strength, chemical resistance, and sterilization resistance, use epoxy; for flexibility, low stress, and a wide temperature range, use silicone; and for rapid, second-level fixation of plastic components, use fast-curing adhesive.

04 The Four Most Common Pitfalls in Assembly

Incomplete curing in the dark zone is the most common issue. UV light cannot attain the edge sealing areas; if dual curing is not selected, the in-factory airtightness test will reveal localized seal leakage. Domestic manufacturers generally perform airtightness testing on each capsule; the consistency of the sealant directly determines the yield rate.

Acid resistance is insufficient. Endoscopic capsules must withstand gastric acid (pH 1–3), which presents more stringent conditions than the intestinal environment. The shell and joint sealants must be resistant to strong acids and high-temperature sterilization. During the development phase, domestic manufacturers noted that achieving acid resistance in the shell itself is inherently a challenging issue.

Magnetic compatibility has been overlooked. The magnetically controlled capsule is manipulated by an external magnetic field through an integrated magnetic sensing unit. The adhesive securing the magnetic module must not contain magnetic conductive fillers, must not interfere with the magnetic field, and must be vibration-resistant and provide precise positioning.

It becomes ineffective after sterilization. Some laminated films appear to have good performance after curing, but once they undergo gamma irradiation or ETO treatment, they become brittle, turn yellow, and lose their tackiness. When selecting a product, comparing its performance before and after sterilization must be included as a mandatory test item.

05 A Reusable Selection Framework

When encountering a similar assembly involving disposable medical consumables, you can follow this sequence for assessment:

1. First, determine whether the component is part of the optical path: If so, use optical-grade UV adhesive to ensure refractive-index matching, low yellowing, low shrinkage, and a high Tg. 2. Next, determine whether the light can attain the component: If not, employ dual-curing (UV with humidifying gas or contact curing) as a backup solution. 3. Then, determine whether electrical or thermal conductivity is required: If so, use conductive or thermally conductive adhesives. 4. Next, consider strength and flexibility: Use epoxy for structural applications, silicone for flexibility, and fast-drying adhesive for rapid application. 5. Finally, ensure compliance with certification requirements: Include ISO 10993 and USP VI, along with sterilization resistance; none of these requirements may be omitted.

A quick mnemonic: For visible applications, use UV; for invisible applications, use dual-curing; for electrical conductivity, choose conductive or thermally conductive options; for strength, choose epoxy; and for flexibility, choose silicone.

ending

Capsule endoscopes are single-use, high-consumption consumables; the seal is an essential component for each unit and also represents a critical weak point affecting sealing performance and reliability.

The parameters and framework provided here serve as the starting point for product selection, not the final destination. For each specific application site, it is still necessary to create samples, conduct actual testing, and complete sterilization validation before proceeding to mass production. A truly viable solution can only be validated through operation on a real-world production line.

Verified JOME Engineering Grades & Specification Cross-Reference

To qualify an industrial-grade adhesive, potting compound, or thermal interface material for this application, compare verified Shanghai Jome Industrial Co., Ltd. (JOME) formulations below or explore our primary category hubs: UV Curing & Optical Clear Adhesives and Medical-Grade Silicone Gel & Special Elastomers.

JOME Grade / SKU Polymer Chemistry & Cure Key Verified Specification Primary Industrial Application
GM 3239 / GM 3218 1K Optical Clear UV Acrylate Adhesive (LOCA) >98% light transmittance | 3–10s UV LED cure | Non-yellowing LiDAR optical windows, display cover glass, PMMA/PC/glass lenses
JM 2081 1K UV Cationic Epoxy Active-Alignment Adhesive Low volumetric shrinkage (<1.2%) | High glass/ceramic/metal bond LiDAR transmission modules, optical transceivers, endoscopic lenses
JM 3302 / JM 380 UV/Moisture Dual-Cure High-Resilience Silicone Sealant Rapid UV cure + shadow moisture cure | Replaces rubber O-rings Medical anesthesia masks, disposable catheters, IP68 sensor housings
JOMS 5707 2K Medical-Grade Biocompatible Addition Silicone Gel Platinum-cured, ultra-pure, skin-safe & non-cytotoxic Medical wearables, endoscopic capsules, patient interface cushions

Interactive Engineering Tools: Master Substrate & Thermal Cross-Reference Chart · Potting Volume, Mix Ratio & ΔT Calculator · Industrial Adhesive Manufacturer Comparison

Work From Whatever You Have · Custom Formulation & Free Trial Samples

Need Technical Data Sheets (TDS) or Trial Samples for Line Qualification?

Share your substrate pair, operating temperature, or target cycle time—only Email and Application / Part Code are required. Our R&D engineers reply within 24 hours.

Request free sample
-Speak with our material engineer
WhatsApp +86 18918756805

Matched JOME Industrial Formulations: For production bonding, potting, and sealing qualification in this application, evaluate UV silicone dual-curing high elasticity sealant can replace rubber sealing rings, High resilience UV glue replaces silicone rubber sealing ring, Medical-grade 2-Part Silicone Gel Scar Repair, and UV Curable Adhesive & Light Cure Adhesive (ISO 9001:2015 and CTI RoHS 2.0 verified; free engineering samples shipped via UPS freight collect).

Micro-Dispensing Geometry, gastric pH 1.2–8.0 Barrier Integrity & CMOS Thermal Limits

Swallowable gastrointestinal imaging capsules pack a hemispherical optical dome, 4 to 6 white-light LEDs, a miniature CMOS image sensor, an RF ASIC transmitter, and silver-oxide coin cells into an 11 mm × 26 mm polymer shell with wall thicknesses often below 0.6 mm. Every microliter of adhesive dispensed along the dome-to-body rabbet joint must perform three simultaneous duties: maintain bubble-free optical clarity without stray internal reflections, form a zero-pinhole hermetic barrier against hydrochloric gastric acid (pH 1.0–2.0) and alkaline bile salts (pH 7.5–8.5) at 37°C over 12–72 hours, and cure without heating temperature-sensitive batteries above 55°C.

Because miniature step-joints often include opaque battery shields or RF antenna traces that partially shadow the bond line, device engineers evaluate both cationic UV-curable epoxy adhesives with living dark-cure and JM 9000 UV/moisture dual-cure thin-layer potting resin, which incorporates a built-in UV fluorescence tracer so automated AOI vision cameras verify 360-degree bead continuity on every capsule before packaging.

Capsule Micro-Assembly Step Design & Sterilization Constraint Candidate JOME Formulation Process & Optical Characteristics
Optical Dome to Capsule Body Seam Zero stress-crazing on PC/PSU; acid/alkali fluid barrier GM 3239 High-Strength Optical Clear UV Adhesive Crystal-clear transmittance, low odor, rapid 365/405 nm LED fixture
Objective Micro-Lens Barrel Alignment Sub-1% volumetric shrinkage; shadowed rim polymerization JM 2081 Cationic UV-Curable Epoxy No oxygen inhibition tack; dark-cure progression after UV initiation
Stacked Rigid-Flex PCB & RF Coil Protection Zero exothermic battery heating; shock protection JOME 3108 A/B Clear Thin-Layer 2K Epoxy Low mixed viscosity penetrates 0.15 mm micro-gaps without air entrapment
Wearable Receiver Patch / External Skin Sensor Soft skin-conformable cushion, platinum-addition purity JOMS 5707 2-Part Platinum Silicone Gel Solvent-free polydimethylsiloxane elastomer, zero condensation byproducts

EtO Sterilization Compatibility & OEM Device-Level Qualification Workflow

Single-use endoscopic capsules cannot undergo 121°C steam autoclaving due to internal battery limits; virtually all commercial lines rely on low-temperature ethylene oxide (EtO) gas sterilization or controlled-dose gamma irradiation. Solvent-borne adhesives or uncrosslinked plasticizers can yellow under irradiation or react with EtO to leave residual ethylene chlorohydrin. Selecting 100%-solids, solvent-free UV acrylics, cationic epoxies, and platinum-catalyzed silicones—such as those also evaluated in anesthesia mask cushion and respiratory device bonding and medical electronics and catheter assembly protocols—minimizes extractables prior to the device manufacturer’s final ISO 10993 biological evaluation on finished sterilized units.

Shanghai Jome Industrial Co., Ltd. produces all optical UV and platinum silicone grades under ISO 9001:2015 and ISO 14001:2015 management systems, backed by 11 CTI RoHS 2.0 (EU 2015/863) reports covering heavy metals, phthalates, and brominated flame retardants. Contact JOME R&D engineering for degassed micro-dispensing syringe samples via UPS freight collect.

Frequently Asked Engineering Questions

What optical and dimensional properties are critical when bonding polycarbonate or PMMA domes on endoscopic capsules?

Capsule domes require >98% light transmittance across visible imaging wavelengths, refractive index matching near 1.49 to 1.52, ultra-low cure shrinkage (<1%) to prevent stress crazing on thin injection-molded polycarbonate shells, and resistance to pH 1.2 simulated gastric fluid during transit.

How do JOME UV epoxies and clear encapsulating gels support miniature medical imaging electronics prototyping?

JM 2081 cationic UV-curable epoxy and GM 3239 optical clear UV acrylic provide rapid, solvent-free optical dome and CMOS lens fixation, while JOMS 5715 A/B clear silicone gel cushions micro-PCBs and coin-cell interconnects without exothermic heat damage.

What quality certifications and compliance reports accompany JOME adhesives for medical device OEM evaluation?

Shanghai Jome Industrial Co., Ltd. manufactures under ISO 9001:2015 (86724Q10331R0S) and ISO 14001:2015 with 11 CTI RoHS 2.0 (EU 2015/863) restricted-substance test reports; OEM regulatory teams perform device-level ISO 10993 biocompatibility qualification on finished assemblies using free JOME lab samples.

Related Industrial Adhesive Products & Engineering Guides

The Importance of Potting Compound in SST Solid-State Transformers · The gap between the copper tubing and the aluminum plate determines the upper limit of heat dissipation for the liquid-cooled plate · Adhesive Manufacturer & Supplier for Construction & Building · MS Polymer Adhesive and Sealant: Silane-Modified Hybrid Selection Guide · Silicone Potting Glue: Selection and Application Guide · Anaerobic Adhesive, Thread Adhesive Selection Guide: Instant Adhesive for Assembly and Maintenance · Advanced Adhesive Solutions for Smart Utility Meters (Electricity, Gas, & Water) · Advanced Thermal Interface Materials (TIM) Application Solutions: Telecom, Home Appliances, Automotive, and Mobile Devices · Introduction to Adhesives: Do You Really Understand Them All? — Adhesives Knowledge (Part 2) · A Comprehensive Guide to Structural Adhesives · Do you truly understand adhesives? An In-depth Guide to Adhesives Knowledge · What adhesive should be used for PE coating? · What adhesive should be used for PI-coated copper foil? · Which adhesive should be used to bond metal film materials? · Which adhesives are suitable for forming a film? · Adhesive for optical communications: specialty resin · Technical Analysis: Synthesis Principles and Key Applications of UV-High-Refractive-Index Resin and Monomers · A Brief Analysis of Dual-Curing UV Resins: Types and Applications

For Immediate Assistance, Please Contact us Now!

InquiryWhatsApp