Adhesive Solution for In Vitro Medical Devices (Monitors, Infusion Pump Housings, Sensors) & Endoscopes

Adhesive Solution for In Vitro Medical Devices (Monitors, Infusion Pump Housings, Sensors) & Endoscopes


1. In Vitro Medical Devices and Endoscopes: Overview
This solution covers two major categories: non-invasive in vitro medical equipment and minimally invasive endoscope assemblies. Adhesive selection must comply with ISO 10993 biocompatibility, withstand repeated sterilization (EtO, gamma irradiation, low-temperature plasma), low outgassing, low extractables & leachables, and match mechanical requirements for rigid housing, precision sensors and flexible endoscope components.
2. In Vitro Medical Devices: Monitors, Infusion Pump Housings & Sensors
Main Bonding Locations & Substrates
Monitor / Infusion Pump Plastic Housing Bonding: ABS, PC, PC/ABS plastic housing assembly, seam sealing, decorative part fixation
Substrates: PC, ABS, PC/ABS, aluminum alloy
Medical Sensors (Pressure, Flow, Temperature Sensors) Bonding: Sensor chip encapsulation, lens bonding, cable sealing, metal pin & plastic housing fixation
Substrates: PC, PMMA, stainless steel, ceramic
Internal Components: Brackets, wiring fixtures, waterproof sealing gaskets
Recommended Adhesive Grades & Process

Recommended Adhesive Grades & Process

Bonding PositionAdhesive TypeKey AdvantagesNotes
PC/ABS housing assembly, transparent lens bondingMedical UV curable acrylic adhesiveFast curing (seconds), high clarity, low shrinkage, automated dispensingRequires light transmission; suitable for non-flexible joints
Metal + plastic structural fixing, sensor pottingMedical two-component epoxyHigh shear & tensile strength, chemical resistance, low shrinkageRelatively brittle; not for dynamic bending parts
Housing seam waterproof sealing, shock absorptionMedical addition-cure siliconeElastic, low stress, good temperature resistance, low outgassingSlow curing, lower bonding strength

Performance Requirements

  • No direct body fluid contact, biocompatibility for incidental skin contact
  • Resistance to repeated disinfection (75% ethanol, isopropanol, disinfectant wipes)
  • Low VOC, no corrosion to electronic circuit
  • Mechanical stability during long-term device vibration

3. Endoscope Adhesive Application (Rigid & Flexible Endoscope)

Main Bonding Locations & Substrates

  1. Distal Tip Assembly: Lens, optical window, CMOS/CCD sensor, metal tip housing
    • Substrates: Sapphire glass, PMMA, stainless steel, PC, ceramic
  2. Insertion Tube & Control Head: Flexible tubing, braided reinforcement wire, plastic connector
    • Substrates: TPU, PEBAX, stainless steel braid, PEEK
  3. Internal Channels & Accessories: Biopsy port, water/air channel, seal rings
    • Substrates: PTFE, silicone, PEEK

Recommended Adhesive Grades & Process

Bonding PositionAdhesive TypeKey AdvantagesNotes
Optical lens, distal tip transparent windowMedical UV adhesiveFast curing, high light transmittance, low shrinkage, precise alignmentMust avoid UV damage to image sensor; control overflow
Flexible tube, PEBAX/TPU tubing bondingMedical polyurethane adhesiveHigh elongation, excellent bending fatigue resistance, good adhesion to flexible polymersTwo-component system, longer curing cycle
Channel sealing, dynamic flexible sealing partsAddition-cure medical siliconeExcellent elasticity, withstand plasma / EtO sterilization, low extractablesPoor adhesion to low-surface-energy plastics; primer may be needed
PEEK/metal structural jointMedical epoxyHigh strength, resistant to strong disinfectantsBrittle, not for bending areas

    Critical Validation Items for Endoscope Adhesives

    1. Biocompatibility: ISO 10993 (cytotoxicity, irritation)
    2. Sterilization resistance: Low-temperature plasma, EtO, gamma radiation; no cracking, discoloration or leaching after multiple cycles
    3. Disinfectant resistance: Stable under repeated soaking in glutaraldehyde, peracetic acid disinfectant
    4. Low outgassing & low extractables: Prevent contamination of optical surface and lumen
    5. Flexibility matching: Flexible section adhesives must follow tube bending without delamination

    4. Common Pitfalls

    1. General industrial UV / epoxy adhesives cannot be used. Even with good bonding strength, lack of ISO 10993 reports will block medical device registration.
    2. PEBAX, PEEK are low-surface-energy materials; surface plasma treatment or dedicated primer is often required.
    3. Endoscope distal tip has heat-sensitive CMOS chips. UV adhesive wavelength and exposure time must be optimized to prevent sensor damage.
    4. Repeated sterilization cycles may cause adhesive yellowing, embrittlement or delamination; accelerated aging test is mandatory.
    5. Adhesive overflow into the lumen will block fluid channel and affect endoscope function; precise dispensing control is required.

    5. Summary

    • In vitro equipment housing & sensors: UV adhesive for transparent precision assembly; epoxy for high-strength static structure; silicone for waterproof sealing.
    • Endoscope: UV for optical tip; PU for flexible insertion tube; silicone for dynamic sealing; epoxy for rigid PEEK/metal joints.

    In Vitro Medical Devices: Map Contact, Movement and Cure Access

    For in vitro medical devices, an adhesive selection review should begin with the specific location of the joint. An enclosure seam, an optical window and a flexible tube connection have different functions and exposure routes. Mark where the cured adhesive can contact the user, fluids or other device materials, including indirect contact paths created by the finished assembly. A housing adhesive should not be assigned the same evaluation solely because another component is used inside the same device. Define the intended cleaning or reprocessing route and whether the part is disposable or reusable. These decisions determine which material interactions need investigation. Next, examine movement. A rigid bracket may need stable positioning, while a flexible tube transition must tolerate repeated bending without placing excessive stress at the end of the bonded region. Adhesive overflow can turn a flexible transition into a locally stiff section, so the dispensing footprint belongs in the design review. In an optical joint, flow into the viewing area can interfere with function even when the bond is mechanically sound. Cure access is another geometry question. Transparent-looking parts do not necessarily transmit the light required by a particular adhesive, and a metal feature can create a shadow beneath an otherwise clear cover. Why choose a rapid light-curing process if part of the actual joint receives no useful exposure? It’s better to verify the light path through the assembled materials than to infer it from their appearance. The UV-curing adhesive material category can help explain that curing route, while suitability for a medical application requires formulation-specific evidence and device evaluation. For mixed materials, consider surface condition, dimensional movement and stresses created during cure. Keep handling stability separate from complete cure. A part that can leave a fixture may still need the remaining process before it is ready for device testing. Document those stages and the material identity so that biological and functional evaluations refer to the same completed assembly process.

    Verify cleanliness, joint integrity and device function together

    Qualification of in vitro medical devices needs more than a visual check that the adhesive has stayed in place. Use representative parts with the actual surface preparation, dispensing pattern and curing route. Examine the joint for bubbles, incomplete contact and material that has entered a channel or reached a sensing surface. Inspection access should be considered before the assembly becomes enclosed. If a feature cannot be inspected directly, choose an appropriate validation method and use separate specimens for sectioning or other destructive examination. Do not infer complete internal filling from a tidy external bead. Check device function before bonding, after cure and after the intended cleaning or reprocessing exposure. A sensor may remain physically attached while its output changes because the surrounding adhesive applies stress. A flexible section may appear intact while resistance to bending increases. Optical assemblies may develop haze, deposits or alignment changes without obvious loss of bond strength. These effects should be recorded as functional changes, rather than being folded into a general adhesion result. Review material interaction under the actual exposure conditions. Resistance to one cleaning agent does not establish resistance to every disinfectant, and evidence from an uncured material does not automatically describe the cured joint. Processing residues, neighboring plastics and the selected curing conditions also belong in the assessment. Keep mechanical performance and biological evaluation as related but separate evidence streams; a strong bond does not answer every question about a contact-sensitive use. Where a joint has failed, locate the separation and compare both surfaces. Poor surface preparation, restricted cure access and stress at a rigid-to-flexible transition call for different adjustments. Use the documented formulation and assembly method when repeating the evaluation, so that a process change is not hidden by the same generic adhesive description. Through JOME adhesive application enquiries, engineers can describe the substrates, joint location, contact conditions and required supporting material information. That enquiry should identify the intended device use clearly without treating a general catalogue entry as proof of suitability. The resulting trial plan can then address the specific bond and the function it must preserve.

    Everything covered here draws on the full JOME product catalogue JOME manufactures in house. Engineers comparing notes with Adhesive Application Protocol for Disposable Medical Catheters can move between the two guides; the the JOME industrial adhesive range frames the range and the talk to the JOME application engineers takes it from there.

    Verified JOME Engineering Grades & Specification Cross-Reference

    To qualify an industrial-grade adhesive, potting compound, or thermal interface material for this application, compare verified Shanghai Jome Industrial Co., Ltd. (JOME) formulations below or explore our primary category hubs: UV Curing & Optical Clear Adhesives and Medical-Grade Silicone Gel & Special Elastomers.

    JOME Grade / SKUPolymer Chemistry & CureKey Verified SpecificationPrimary Industrial Application
    GM 3239 / GM 32181K Optical Clear UV Acrylate Adhesive (LOCA)>98% light transmittance | 3–10s UV LED cure | Non-yellowingLiDAR optical windows, display cover glass, PMMA/PC/glass lenses
    JM 20811K UV Cationic Epoxy Active-Alignment AdhesiveLow volumetric shrinkage (<1.2%) | High glass/ceramic/metal bondLiDAR transmission modules, optical transceivers, endoscopic lenses
    JM 3302 / JM 380UV/Moisture Dual-Cure High-Resilience Silicone SealantRapid UV cure + shadow moisture cure | Replaces rubber O-ringsMedical anesthesia masks, disposable catheters, IP68 sensor housings
    JOMS 57072K Medical-Grade Biocompatible Addition Silicone GelPlatinum-cured, ultra-pure, skin-safe & non-cytotoxicMedical wearables, endoscopic capsules, patient interface cushions

    Interactive Engineering Tools: Master Substrate & Thermal Cross-Reference Chart · Potting Volume, Mix Ratio & ΔT Calculator · Industrial Adhesive Manufacturer Comparison

    Work From Whatever You Have · Custom Formulation & Free Trial Samples

    Need Technical Data Sheets (TDS) or Trial Samples for Line Qualification?

    Share your substrate pair, operating temperature, or target cycle time—only Email and Application / Part Code are required. Our R&D engineers reply within 24 hours.

    Matched JOME Industrial Formulations: For production bonding, potting, and sealing qualification in this application, evaluate Medical-grade 2-Part Silicone Gel Scar Repair, UV Curable Adhesive & Light Cure Adhesive, UV light rapidly cures thin-layer Potting Compound, and High bonding strength Optical transparent UV adhesive (ISO 9001:2015 and CTI RoHS 2.0 verified; free engineering samples shipped via UPS freight collect).

    Frequently Asked Engineering Questions

    Which JOME adhesive or potting grades are recommended for adhesive solution for in vitro medical devices (monitors, infusio?

    Depending on substrate pair, continuous operating temperature, and curing line constraints, Shanghai Jome Industrial Co., Ltd. (JOME) recommends evaluating GM 3239 / GM 3218, JM 2081, and JM 3302 / JM 380. Review our full specification table on this page or request a customized formulation sample.

    Can JOME customize viscosity, cure speed, or thermal conductivity for our automated production line?

    Yes. JOME's Shanghai RandD laboratory customizes A/B mix viscosity, thixotropic index, pot life, Shore hardness, and thermal filler loading (0.75 to 25.0 W/m·K) to match your dispensing equipment and environmental test standards.

    Related Industrial Adhesive Products & Engineering Guides

    Silicone adhesive for hardware · What adhesive should be used to bond silicone sealing rings? · Which materials can be bonded using liquid hot-melt adhesives? · Can powdered fillers be added to adhesives? · Applications of Silicone Materials in UV-Curing · Understanding UV Viscosity in One Article: Core Insights into Resins, Coatings, Inks, and Adhesives · "Hidden Materials" in the Photovoltaic Industry: UV Coatings and UV Adhesives · Wind Turbine Whole Machine Adhesive Solution (Onshore + Offshore Wind Power)-Cowlings, Interior Assembly of the Machine · Sealing materials for vehicle oil circuit components – fluorosilicone rubber and fluorosilicone gel · New energy vehicle thermal management solution · The scheme for the adhesive application areas in car body assembly · Recommended adhesive solution for power controller · The application of high-performance adhesives in lithium battery modules · Analysis of Adhesives for Power Batteries in New Energy Vehicles · Medical Device Adhesive Solutions · A comprehensive bonding solution for the wind power industry (including onshore and offshore wind power) · Complete Adhesive Solutions for Industrial & Consumer Electronics · Thermally conductive adhesive

    For Immediate Assistance, Please Contact us Now!

    InquiryWhatsApp